• Covington Manning posted an update 2 months, 3 weeks ago

    Inside painting requires as careful preparation of surfaces as does exterior painting. The introduction of odorless paints now can help you paint any time of the year. Formerly, most interior painting in the home was done in the drop or spring, when it was possible to leave the windows open to ventilate the area. But open windows brought dirt in to the room to mar the finished painted surface.

    An excellent interior paint job is often 50% planning and 50% painting. Usually do not rush in preparing the floors in your eagerness to access the brush or roller. If you don’t prepare the surfaces properly, you’ll be back with the paint brush or roller in a few months.

    In this section you will discover the necessary information on the application of various kinds of paints on various interior walls, ceiling and floor materials.


    New dry plaster in good condition, which is to be finished with a paint apart from water paint, ought to be given a coat of primer-sealer and allowed to dry thoroughly before becoming inspected for uniformity of appearance. Variations in gloss and shade differences regarding tinted primers indicate set up whole surface has been entirely sealed. If not, a second coat of primer-sealer ought to be applied. If only a few "suction spots" are apparent, another coat over these areas could be sufficient.

    A set, semi-gloss, or high-gloss finish may be put on the primed surface. For a set finish, two coats of toned wall color should follow the priming coating. For a semi-gloss surface finish, one coat of flat wall paint and one coat of semi-gloss paint should be applied to the primed surface. For a high-gloss surface finish, one coat of semi-gloss color and something coat of high-gloss enamel ought to be used on the priming coat.

    Before applying drinking water paints of the calcimine form to new plastered walls they should be sized, using the glue-water dimensions or, if the plaster is definitely dry, a slim varnish or primer-sealer.

    Cool water paints of the casein sort may be applied either right to a plastered surface, or the top could be first given a coat of primer-sealer to equalize uneven suction results. The same is true of resin-emulsion paints, with the recommendations of the manufacturer of the merchandise being given preference in case of doubt. Since resin-emulsion paints usually contain some oil in the binder, they should ordinarily be applied and then plaster which includes dried thoroughly.

    Texture wall paints may also be used on plaster surfaces. The advantages of this kind of paint are that one coat economically creates a textured decoration and relieves the monotony of clean flat paint. It also covers cracks or patches in the plaster considerably more completely than ordinary wall paint. The cons of texture wall color are that they Collect dust and are difficult to restore to a smooth surface finish. These materials can be found as water-or oil-based paints, are usually thicker than ordinary wall paints, and could be applied to wallboard and plaster to produce textured effects such as random, Spanish, objective, and multicolored.

    Composition Wallboard

    Composition wallboard normally presents no particular painting troubles if the ordinary precautions are observed, such as making certain that the surface is dry and clear of grease and essential oil. The painting procedure for wallboard is the same as for plaster; it needs a priming and sealing layer accompanied by whatever finishes coats are desired, or could be given one-coat smooth or resin-emulsion type paint.


    Water-thinned paint may be put on wallpaper that is well- bonded to the wall structure and will not contain dyes which may bleed into the paint. One thickness of wallpaper is certainly preferable for color application. Paints apart from those of the water-thinned kind can also be applied to wallpaper by following the directions given for painting plaster. However, wallpaper coated with such a paint is difficult to eliminate without problems for the plaster.

    Wood Walls and Trim

    New interior walls and wood trim ought to be smoothed with sand-paper and dusted before painting or varnishing. To preserve the grain of the wood, the surface may be rubbed with linseed essential oil, varnished or shellacked, and waxed. If an opaque end is desired, semi-gloss paint thinned with 1 pint of turpen-tine per gallon of color or the primer-sealer in the past described for walls may be used as a priming coat on wood.
    Franklin Painters A couple of coats of semi-gloss color should then be applied over the thoroughly dry prime layer, or if a full-gloss finish is desired, the final coat ought to be a high-gloss enamel.

    Masonry Walls and Ceilings

    Interior masonry walls and ceilings above quality may, generally, be painted in quite similar manner as plaster surfaces. In this article again, it is necessary to allow adequate period for the masonry to dried before applying paint and, furthermore, attention should be given to the preparation of the surface. When decorating a wall structure containing Portland cement (concrete, for example), it is essential to take precautions against the attack of alkali. For this function, alkali-resistant primers such as rubber-base paints may be used when oil paints are to check out.

    Cement-water paints are best suited for application to basement wall space which are damp because of leakage or condensation. To apply these paints, exactly the same procedure ought to be followed as is described here for painting exterior masonry walls.